The core problem of compressor oper
Comprehensive analysis of floor heating module knowledge, hurry up and learn!
Floor heating is a heating method that uses ground radiation to dissipate heat. For a long time, heating in northern areas has been dominated by radiators. In its use, its shortcomings will bring a lot of inconvenience, and the emergence of floor heating modules has become a necessity. As the main component at the end of the geothermal heating system, the floor heating module greatly simplifies the installation procedure of the floor heating, and also provides a lot of convenience for the future maintenance of the floor heating.
Floor heating module-types of floor heating
Floor heating modules can be divided into: plastic modules, metal and thermal insulation material composite modules, cement modules, etc. according to materials. According to the appearance form, there are template type modules, pipe trough type modules, M-type floor heating modules, etc.
Floor heating module-circuit system
The power main line enters the module wiring slot, and the heating plate is connected to each other in the wiring slot. Each module is connected to the main line. The main line passes through the wiring slot, and each branch line will produce a joint. In this case, the number of underground joints will be more.
Floor heating module-heating system
600*1200mm adopts heating module board for heating, the heating area is 600*1100mm, basically there is a 100mm cooling distance between each module. And there is a certain installation gap between each module, which directly leads to uneven heating on the ground.
Floor heating module-installation method
After laying the wooden floor, when heating the wooden floor for s* times, choose to gradually increase the temperature, the purpose is to prevent the wooden floor from being twisted and deformed during the heating process. In general, experts suggest that the temperature rise should be about 2 to 5°C per hour, but for such a precise temperature, it can be done accurately except for the wall-hung boiler, but how can it be accurate? Experts suggest that you can close the trap valve after heating for an hour, wait an hour or open the valve again to make the water supply temperature gradually close to about 2 to 5 ℃ per hour, so that the problem of uniform heating can be fully solved.
Floor heating module-core advantage
1. Environmental protection and energy saving: Compared with traditional heating products, energy saving is about 10%. The raw materials are all environmental protection and energy saving products.
2. Simple and generous: The design is simple and generous, easy to install.
3. Reliable quality: resistance to acid, alkali and salt corrosion, high pressure, high temperature, penetration resistance, no rust, infertility, tube scaling, inner tube 4. Smooth connection, low friction.
5. Uniform heat dissipation: evenly distributed on the ground, using the characteristics of human body temperature, and small air flow.
6. Clean and healthy: There is no dust in the room, and it can promote the blood balance of the human body, prevent and treat key inflammations, old cold legs, and improve autoimmunity.
7. Long life: 3-5 years longer than ordinary floor heating modules.
8. Sound insulation and high efficiency: The warm and easy floor heating module floor heating increases the insulation layer, has very good sound insulation results, can reduce noise pollution, and there is no noise during the heating process, which is beneficial to the physical and mental health of the family.
Floor heating module-matters needing attention
At the same time, users need to pay attention to that any wooden floor has the possibility of thermal expansion, so the wooden floor needs to be properly humidified in addition to the temperature rise. Since many floors will lose moisture when the temperature rises, proper indoor humidification and maintenance is very helpful for the floor to lose too much moisture and cause dry cracking and deformation. In addition, when the water floor heating module is stopped, the floor temperature will inevitably decrease. When it is lowered, the floor temperature must be gradually reduced to avoid excessive moisture absorption and expansion of the floor, thereby affecting the service life of the floor. Therefore, use it reasonably during the use of the floor heating module. The method will extend the life and give full play to the effect.
Based on the above comprehensive introduction of the classification, system, installation, advantages and precautions of the floor heating module, I believe that users have already understood the electric heating module. "Three points for the floor, seven points for installation" is also true. The floor heating module is closely related to the energy efficiency of floor heating in the future, regardless of installation or appearance. In addition, future maintenance and maintenance are also indispensable, so as to help the floor heating module to achieve the best use effect.
