Chint Relay JSZ3F 60s AC220V

06/29/2020

How the compressor works

07/08/2020

Cold storage standard installation and commissioning strategy

Cold storage standard installation and commissioning strategy 1. Installation Specification of Cold Storage 　　 Enter the construction site, according to the construction drawings, verify the implementation of the work, determine the installation location of the equipment (storage body, drain door, evaporator, host, condenser, control system, etc.).

06/14/2020

Refrigerating oil replacement and internal cleaning

Refrigerating oil replacement and internal cleaning The operation of draining oil is as described above. After the freezing oil is removed and the pressure inside and outside the compressor is balanced, use an allen wrench to loosen the flange bolts and 器2䀀
ￜ皥
䖒皦즠Ʋ奌ི㲈Ʋ
䌁皦
ᮔDž༬皧奖ིЀ呄ᠾ鹨់༹皧
ࠄ
00령ꐱ댁珵뛐珵Љ
䕄ྦ￿￿뤂ᐱ뚜珵ᴴᏩ呄ᠾ퍘ᒥ鹨់ᩄꋔྦ
瑉浥巠皱㙲皦抐皱巠皱੨皦柘皱ￜ皥
ب巠皱㙲皦忈皱੨皦柘皱
즠Ʋǜ勁皦즠ƲبǜV /펔B䌁皦
ᮔDž'鱤džၜ먢䇨珵呈ᠾ뤂ᐱ⿇⬿먲僧ᐱ㥲ᐲ�僬㣢ᐲᠾ
랖僧٢識�僬㣢ᐲ臆S㥲ᐲᬄğ識理艏S杴 識杴 㥲ᐲ

06/14/2020

Heating principle

Heating principle

08/20/2020

How to prevent moisture caused by steam penetration in cold storage projects

Under normal circumstances, excessive air humidity causes rapid growth of mold, moldy food, and corrosion of cold storage building materials. Therefore, the moisture-proof of cold storage projects is also particularly important.

03/02/2021

Connection between Arduino and servo motor

The connection of the servo motor using Arduino is as follows: Connect the black wires on the two servo motors to the GND on the Arduino Connect the red wires on the two servo motors to the 5V pin on the Arduino Connect the yellow wire on the first motor to pin 8 on the Arduino

09/08/2020

What are the functions of the air compressor dewatering device

The compressed air produced by the compressor is not pure. This is because the air compressor itself contains lubricating oil. During the compression work, part of the lubricating oil must be mixed into the compressed air.

07/13/2020

Danfoss training-common faults and analysis of compressors

Danfoss training-scroll compressor I participated in Danfoss' service provider training and learning twice a week this week, mainly on scroll compressors (MLM series, MLZ series, LLZ series), and the recently hot scroll compressors for heat pumps (SH series, PSH series) ). And analyze the common faults of the compressor and exchange solutions.

09/06/2020

Main properties of permanent magnet materials commonly used in motors

Permanent magnet materials commonly used in motors include sintered magnets and bonded magnets. The main types are AlNiCo, ferrite, samarium cobalt and neodymium iron boron.

06/30/2020

What are the factors that cause motor damage？

What are the factors that cause motor damage？ What are the factors that cause damage to the compressor motor: 　　 1. Abnormal load and stall